E2EQ-IL

Funktioner

Flourplastbelagda induktiva givare med IO-Link är en innovativ lösning för att lösa svetsrelaterade problem i industriella tillverkningsanläggningar.

  • Minska antalet driftstopp med inbyggda diagnostikfunktioner
  • Antalet plötsliga fel kan undvikas genom förtida signal om att avkänningsavståndet ökat eller minskats
  • Underhållsarbetet blir mer effektivt genom att man identifierar varje givare via IO-Link-nätverket
  • Programmerbar givare gör att det inte behövs lika många olika modeller
  • Fluorplastbeläggningen ger högt skydd mot svetsloppor i fordonsindustrin och maskinverktygsindustrin
Tekniska data

Ordering information

DC 3-wire IO-Link models

Appearance

Sensing distance

Connection method

Cable specifications

Operation mode

Pin arrangement

Baud rate

Order code

 

M12

3 mm

Pre-wired models (2 m)

PVC

NO/NC
switching

COM2

E2EQ-X3B4-IL2 2M

COM3

E2EQ-X3B4-IL3 2M

M12 Pre-wired Smartclick connector models (0.3 m)

1: +V

3: 0 V

4: C/Q output

COM2

E2EQ-X3B4-M1TJ-IL2 0.3M

COM3

E2EQ-X3B4-M1TJ-IL3 0.3M

M18

7 mm

Pre-wired models (2 m)

COM2

E2EQ-X7B4-IL2 2M

COM3

E2EQ-X7B4-IL3 2M

M12 Pre-wired Smartclick connector models (0.3 m)

1: +V

3: 0 V

4: C/Q output

COM2

E2EQ-X7B4-M1TJ-IL2 0.3M

COM3

E2EQ-X7B4-M1TJ-IL3 0.3M

M30

10 mm

Pre-wired models (2 m)

COM2

E2EQ-X10B4-IL2 2M

COM3

E2EQ-X10B4-IL3 2M

M12 Pre-wired Smartclick connector models (0.3 m)

1: +V

3: 0 V

4: C/Q output

COM2

E2EQ-X10B4-M1TJ-IL2 0.3M

COM3

E2EQ-X10B4-M1TJ-IL3 0.3M

Specifications

DC 3-wire IO-Link models

Size

M12

M18

M30

Item

Model

E2EQ-X3B4-IL_

E2EQ-X7B4-IL_

E2EQ-X10B4-IL_

Sensing distance

3 mm ±10%

7 mm ±10%

10 mm ±10%

Set distance1

0 to 2.4 mm

0 to 5.6 mm

0 to 8 mm

Differential travel

10% max. of sensing distance

Response frequency2

1 kHz

0.5 kHz

0.4 kHz

Power supply voltage

10 to 30 VDC (including 10% ripple (p-p))

Current consumption

20 mA max.

Control output

Load current

100 mA max.

Residual voltage

2 V max. (Load current: 100 mA, Cable length: 2 m)

Indicators1

In the Standard I/O mode (SIO mode): Operation indicator (orange, lit) and stability indicator (green, lit)

In the IO-Link mode: Operation indicator (orange, lit) and communication indicator (green, blinking at 1 s intervals)

Operation mode

PNP NO/NC switching type (Factory setting: NO)

Degree of protection

IEC 60529 IP67, in-house standards: oil-resistant

Connection method

Pre-wired Models (Standard cable length: 2 m), Pre-wired Connector Models (Standard cable length: 0.3 m)

Materials

Case

Fluororesin coating (Base material: brass)

Sensing surface

Fluororesin

Clamping nuts

Fluororesin coating (Base material: brass)

Toothed washer

Zinc-plated iron

Main IO-Link functions

Operation mode switching between NO and NC, self diagnosis enabling, excessive proximity judgment distance selecting, timer function of the control output and timer time selecting, instability output (IO-Link mode) ON delay timer time selecting function, monitor output, operating hours read-out, and initial reset

Communication specifications

IO-Link specification

Ver 1.1

Baud rate

-IL3: COM3 (230.4 kbps), -IL2: COM2 (38.4 kbps)

Data length

PD size: 2 bytes, OD size: 1 byte (M-sequence type: TYPE_2_2)

Minimum cycle time

-IL3 (COM3): 1 ms, -IL2 (COM2): 2.3 ms


1. In the Standard I/O mode (SIO mode), use the product in a range that the green stability indication lamp is lit. (Although the lamp is turned off when the object detected has approached excessively, the detection performance is stable.)
In the IO-Link mode, use the product in a range that the Byte1_bit4 for instability detection is zero. (Although the Byte1_bit5 for excessive proximity detection is one if the object detected has approached excessively, the detection performance is stable.) Please contact your OMRON sales representative regarding assignment of data.
2. The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance.
1. In the Standard I/O mode (SIO mode), use the product in a range that the green stability indication lamp is lit. (Although the lamp is turned off when the object detected has approached excessively, the detection performance is stable.)
In the IO-Link mode, use the product in a range that the Byte1_bit4 for instability detection is zero. (Although the Byte1_bit5 for excessive proximity detection is one if the object detected has approached excessively, the detection performance is stable.) Please contact your OMRON sales representative regarding assignment of data.
2. The response frequency is an average value. Measurement conditions are as follows: standard sensing object, a distance of twice the standard sensing object, and a set distance of half the sensing distance.
Tillbehör

XS2

XS2_OEI.jpg
XS2 Connector Cordsets with M12 watertight single-ended and extension cordsets.

XS3

XS3_OEI.jpg
XS3-kontaktkabelsatser med M8-kabelsatser och förlängningskabelsatser för minskat underhåll.

XS5C/XS5G

XS5C_XS5G_400x400.jpg
XS5C/XS5G-D418-kontakter av IDC-typ har utvecklats särskilt för snabb och enkel anslutning utan specialverktyg.

Y92E-S_PP

Y92E-S_OEI.jpg
IP69K-klassade kabelsatser med sensorkontakter för tillämpningar inom livsmedel, drycker och läkemedel

Prenumerera på produktuppdateringar

Nyhetsbrev om produktinnovationer, system och tjänster, direkt till din inkorg.

Tack för att du väljer att prenumerare på eNews. Du kommer inom kort att få ett e-postmeddelande från oss med en länk för att aktivera din prenumeration.

Vi har tekniska problem. Din formulär har inte varit framgångsrik. Vi ber om ursäkt och försök igen senare.

Download

Produktdokumentation

Hämta datablad, handböcker och broschyrer.

Sök i hämtningscentret

Kurser

Utbilda dig hos våra bästa tekniker. Från nybörjarnivå till avancerad nivå.

Visa kurser